Lonsdor K518ISE

Lonsdor K518ISE
Lonsdor K518ISE

2018-01-30

OBDSTAR BT06 Car Battery Tester User Manual

Step by step procedure on how to use OBDSTAR BT06 Car Battery Tester.

Connect OBDSTAR BT06 device with the battery
Put the red and black clamp to the battery to be tested. Red clamp for positive, black clamp for negative. It will show start-up interface on the screen.
The voltage of the battery to be tested should be lower than 6.0 V or the normal test is unable to proceed; Press OK to continue.


According to the prompt of the device, select in proper order
Step1: Choose the testing state
It refers to if the battery is inside the vehicle with load connected. If so, choose [Inside vehicle]. If not, choose [outside vehicle].

Step2: Choose charge state
It refers to if the charge of the battery is finished. If so, choose [After charge]. If not, choose [Before charge].


Step3: Choose battery type
It refers to the battery type. Choose [Normal battery] in general.


Step4:Choose input standard
It refers to the factory marked standard for the battery, which is shown on the right above or the front battery. Choose the marked standard, such as CCA, JIS and etc.
If there is no standard shown, please select GB standard and input the Ah value to test. The error will be less when selecting GB standard.



Step5: Choose rated capacity
It refers to factory starting current standard, which is shown on the right above or the front battery. Such as 55B24.


Step6: Press ok to begin the test
Test results interpretation


Tip:
Notice: For some batteries in deep lack of power (the vehicle is not used for a long time, batteries are not charged in time; battery is in deep lack of power because of not turning off lamp and door that can not start the vehicle and etc), there will be a prompt “please replace the battery”. For this kind of battery, please consult with the battery manufacturer fist and replace and charge the battery according to the method given by the manufacturer, and then begin the test.
Start system test
Step1: After the battery test is finished, please press [OK] to enter starting system test if the testing state is inside vehicle as shown below.



Step2: Start the engine according to the prompt and the device will finish the starting system test automatically and show the result.


Step3: Test result includes start time, start voltage and voltage state.(In general, start voltage lower than 9.6v is abnormal, higher than 9.6v is normal.)


Step4: If the starting system test is abnormal, the battery test results are displayed.



In this way, the maintenance personnel can quickly determine the overall condition of the starting system according to this data.
Charging system test

  • After starting system test is finished, please press [OK] to enter Charging system test and operate according to the prompt and “please seep up to 3000 RPM and keep for 5s”


  • After test is finished, the device will show charging voltage, on-load voltage and diode ripple as shown below.


Notice: If the device can not detect the engine speed, there is probably something wrong with the engine regulator or the connection breakdown with the battery. If the device can not detect the charging voltage, the device can skip the engine speed test, then the result will show  “No voltage input”. Please check the connection between engineer and battery and then test again.

Results for charging system test

Charging voltage: normal
The charging system shows that the output of the generator is normal and no problems are detected.

Charging voltage: low
Insufficient charging voltage of charging system
Please check whether the generator belt is skidding or disconnecting, check whether the connection between the generator and the battery is normal.
If the transmission belt and circuit is connected well, please troubleshoot the generator according to the manufacturer's suggestion.

Charging voltage: high
The voltage for generator output is too high.
As most generators in the cars use a built-in regulator, it needs to replace the generator assembly (some older cars which use external regulators, please replace the regulator directly).
The limit of usual high voltage limit in a car regulator is 14.7v. Charging too high will make the battery go through charging, thus shortening the life of the battery and causing it to malfunction.

No voltage output:
The generator voltage output is not detected. Table check whether generator connections and generator belts are normal.

Diode testing:
The tester can detect whether the diode is normal by charging current waveform. If the diode wave voltage is too high, then at least one diode has been damaged, please check and replace the diode. So far, the test is completed.

http://www.eobdtool.co.uk

2018-01-29

Reviews of CGDI Prog MB


After the CGDI Prog MB released, many people will compare it with VVDI Prog.Here post some reviews from TechnoloGY Forum. Hope they could help you to choose your key tool.


Perso69:
Sprinter W906 2010 report:
Adding key success by user on Sprinter W906 2010 with BGA key
Key add on car by OBD
Also W210 add key on bench with NEC key: Success.

Perso69:
Update from CGDI version 2.2
204 all key lost bug is really solved.
ELV function seem work OK.
CGDI Prog MB to do W221

ROD-BENDERS:
Benz Monster has arrived and it looks good so far, It came packaged with a free opcom 1.95 which was a nice touch smile1I also ordered some keys and they are top quality, look and feel like the genuine items.

Sqlkarol:
Last week i doing EIS W203 on table.
I read HC12 by VVDIProg.
Then calculated keys CGDI MB.
I renew used (original MB) NEC key within adapter, then programming.
Key works.
All ok.

Perso69:
When i see price go up, that meaning tool become really good update after update.
I'm not saying tool is better than others, but for the thing it do (making key, spare or lost in CAN system) it is simple amasing fast and effecie.
ECU function will release later, one week? or some weeks? No one know yet.

New report from Japan friend:
W164 ML450 2009 spare key in 15mn all done.

From Canada:
W204 all key lost on bench:
40mn collect data, 10mn PSW calculation
He did with diagram connection i've made on bench.

Jarsar:
Yesterday I did key x164 GL 2012.
All OK.
All done in 10-12 mn.

Mar.wo:
Hi Bros
I did my first in life Benz, it was W169/2010 and i out out password and added extra key btw. it was Chinese BGA 3 buttons from Anna, it taken about 10min. Great.

With all the feedbacks above, we hope you can find a good tool for car program.

If you have interest in CGDI Prog MB, please click:

2018-01-28

Ford IDS V108.01 full software download


Ford IDS V108.01 software tested and performed well before released. The following will tell you where to download it safety and what Ford diagnostic interface does Ford IDS v108.01 work with.


Where is good place for Ford IDS V108.01 Full Software download?
Compatible with XP 7 32 64bits
Language options: English, French, Spanish, Italian, Polish, Portuguese etc.
Feature: Online programming is working great if you have online account.

What Ford diagnostic interface does Ford IDS V108.01 work with?
How to choose a good VCM2? read 4 typical VCM2 clone
- Ford VCM II original (Google to research)
How to install & activate Ford IDS V108.01 Full Software?
If you bought from the above shop, the supplier will help setup & activate with TeamViewer remote assistance, even need no wait for the CD package.

What does Ford IDS V108.01 Full Software can do:
V108.01 IDS also have the ability to download the very latest calibration/software files from ford's server if you have an internet connection available at the time of connecting to vehicles. (Confirmed)

Reading and decoding fault codes (Confirmed)
Deleting fault codes (Confirmed)

Display System current parameters in digital form (Confirmed)

Combined displaying of data (Confirmed)

Logs Keeping: writing and keeping of digital parameters in memory (Confirmed)

Special functions: changing of permissible seeting of blocks, programming etc. (Confirmed)




2018-01-24

Foxwell NT510 Scanner Discussion

This post will share you with some frequently asked questions about Foxwell NT510 Scanner. Hope these could help you.


Question:
Is this compatible with 2008 bmw 750li obd? i am not sure of which code will my 7 series fall in, hence i asked.
Answer:
The scanner can support the BMW 750li, it can not only support most system scan, but also support some service functions such as ABS/DSC final check,Bleeding, precharging pump circuit,Bleeding, DSC hydraulics,EWS/DME alignment,ect.

Question:
Will this scanner register a new battery in a 2011 bmw 335i (e90)?
Answer:
Yes, it supports register battery replacement. 

Question:
Can this scan the airbag system and return the code?
Answer:
Yes, it's can scan the airbay system and clear teh code. 

Question:
I have a 2015 chrysler 200 and the ecu is damage I bought a new ecu from Ebay but now I need to reprogram it to the car well these doo the job.
Answer:
The answer is yes, you go to their web sight an I think it's 60$ to down load for a different car 

Question:
Can this tool program a new key to a 2006 BMW 530?
Answer:
This tool does not program the key fob. You'll need to go to the BMW dealer. It will calibrate the steering clear codes like engine light and program new battery and more. Its a very helpful tool and a must have. 

Question:
Can it engage the fuel pumps on a 2010 335d when the fuel filter needs changed?
Answer:
Yes it can. For full specifications and coverage please check with the manufacturer official page. There is a full list of specifications there. 

Question:
Does this scanner include the 18 month software update after purchase that I have seen on other Foxwell reale websites?
Answer:
Yes, it include 18 month software update after you registration.

Question:
Will this work resetting a bmw 328i 2007 agm battery code?
Answer:
Yes, it can reset the bmw 328i agm battery code. 

Question:
Does this scanner allow you to reset a frm module on a bmw e90 (2006 330i)?
Answer:
Hi, did you mean FRM footwell module ? If it is, the scanner can support it. 

Question:
If you dont purchase updates after the free 18 month update period, will the scanner still fully function?
Answer:
I have this scanner and according to Foxwell. Yes what is on the Scanner does stay active. Just no updates beyond. Tony 

Question:
I have a dsc code on my 03 bwm 745li, will it tell me what the trouble is?
Answer:
Yes, absolutely ma nig. 

Question:
Will this work on new bmw's and can it read "shaddow codes" not just generic odbii codes ?
Answer:
It works with my 04 and should work with newer models also. This unit will communicate with all the cars modules and reset all codes. 

Question:
will this scanner work on 2004 vw taureg . and how much is the cost of upgrading to all other cars.
Answer:
Thanks for your inquiry. The FOXWELL NT510 BMW can not work on 2004 vw taureg. The FOXWELL NT510 VAG will work on it. Besides, one NT510 can install up to five diagnostic software, each software is $60 around, look here: http://www.eobdtool.co.uk/wholesale/foxwell-nt510-software.html

Question:
Will this work for a 2001 530i for abs light and 2001 328i Airbag light reset?
Answer:
Yes, it will. 

Question:
Does it support Td5 engines
Answer:
Yes 

Question:
I cant gind battery reset function for vmw 328I.
Answer:
Please find you car model and year first, when you enter the "Main Groups", choose "Service"---"Body" 

Question:
Can it read the transmission temperature of a dodge
Answer:
Hi, the NT510 BMW diagnostic tool is especially for BMW/MINI/Rolls-Royce, it can't read the transmission temperature of a dodge. 

Question:
Hi, I have an e90 328 and an e92 M3, will this scanner read all BMW-specific codes?
Answer:
It should cover it. The latest software update even mentions how it added more BMW models support. On the scan tool, when you're at the part where you choose your BMW model type, the list is really long, so I'm pretty sure your e90 and e92 will be on the list. Sorry I cannot check right now because I don't own a BMW, but used it on a couple of friend's BMWs.
Once you select your BMW model and run the auto-scan, it will check every system in your car, not just the typical OBD II stuff that most common scanners only support.

Question:
Can this tool diagnose my suspension air ride on a 2007 x5
Answer:
Yes

Question:
can this tool program GM key fob remotes for 2012 models?
Answer:
not support 

Question:
Well this work on mu car 2010 X5 M
Answer:
I Believe it works on all bmw models. Double check with the seller. Works perfectly for my 2008 535xi. If you are doing multiple checks- make sure your battery is in good shape. 

Question:
Does this work for 2011 bmw m3 v8 with abs/dbc warning lights? diagnostic and clear
Answer:
Yes 

Question:
Is this compatible with 2014 bmw x5 and if so do i have to buy a connector that fit in my bmw x5?
Answer:
Yes this will work with you car however what they fail to mention is that you need to purchase the diagnostic software modules separately. I returned mine because of this.

Question:
Can NT510 adaptation the bmw
Answer:
Yes, as for the hardware/plug, this will work directly with the "newer" BMW OBDII 16-pin connector found under the dash driver side, but you will need an adapter for the older 20-pin style plug found under the hood in engine compartment area.
The default software is the standard OBDII scanning software - good for most diagnostics/SMOG. This unit comes with one additional specialized software, in this case for BMW/Mini's, so does a good job in diagnosing all onboard modules and trouble codes. It is fairly in-depth, I believe it communicates with 12-14 of the various diagnostic computers on a BMW - allowing for not only ideal readouts, but also real-time data diagnostics (while engine running) for displaying in a matrix or graph. If you have other cars, you can also purchase/add additional software modules from Foxwell or 3rd party - you can have up to 5 different automobile makes using a single handheld scanner.
Cons- The purchase of additional software is not as straight forward, as their website support and directions are not as clear as they should. Speaking of support, I believe their support is overseas (China), so speaking to a live person is not possible - you will have to open a support ticket, shall the need arise, or send an email (I did both) and someone will respond back next day or two.
Hope this helps 


Foxwell NT510 car list and functions:


More posts about Foxwell NT510:
Foxwell NT510 Support:

So the Schwaben Scan Tool I Bought is Foxwell NT510:

BMW DIY Repairing Best Choice: Foxwell NT510 Scanner Feedbacks

I have had good success with BMW Use Foxwell NT510

Best Sale in eobdool.co.uk: