Lonsdor K518ISE

Lonsdor K518ISE
Lonsdor K518ISE

2018-04-30

SEC-E9 Bluetooth Disconnection or Drop Solution

SEC-E9 is a powerful Key Cutting Machine based on its Bluetooth connection. Once the Bluetooth disconnection, the machine won’t work properly. This post will express the situation why Bluetooth disconnect and how to solve this problem.

There are two reasons why fail to connect Bluetooth:
1) Incorrect boot sequence
2) Bluetooth module is dropped by interference

Now, solution will be given one by one.
1. Incorrect boot sequence
The correct boot steps:
A. Connect the power switch with power supply (Input Voltage is DC 100-240V) .
B. Clockwise twisting switch to turn on the machine, and then long press the switch of tablet till logo appears.
C. Please wait seconds, SEC-E9 will go to main page automatically.
D. Once you see the main page of SEC-E9 in tablet, it means the tablet and the machine get in touch with each other successfully.

Here is the guide how to reboot SEC-E9 when something happen:
A. Press “Shutdown” button in the main page.
B.  Press the power switch to turn off the machine.
C. Please wait for 2 minutes and then strictly follow in boot steps to do.
 Attach a video to show how to turn on and turn off SEC-E9:


2. Bluetooth module is dropped by interference
 Solution:
Firstly follow the correct steps to turn on SEC-E9. Please check the area in below picture, if it light blue means that Bluetooth module operate normally, it will automatically match and take tens of seconds, please be patient and don't touch any button on the screen.


If the Bluetooth disconnects, please find the Bluetooth serial number by clicking the Bluetooth icon in the lower right corner, and click “remove device “and “Pair” again. Enter password “8888” and click “next”. If you can enter the main page successfully, that means the Bluetooth setting is completed successfully.

Last but not least, if you follow the correct boot way above, but the blue light is not light in that area, please contact with our support team, we will guide you online how to deal with it.


2018-04-28

Success: How Launch CReader 9081 Diagnose VW

Launch Creader 9081 is a light but smart diagnostic & reset service tool which has 11 reset functions like full OBD2 scanner+ABS+SRS+Oil+EPB+BMS+SAS+DPF. This post generally shows how to use it to diagnose VW incl. read & clear fault codes, read data stream, O2 sensor test ...


1. Plug Launch CR9081 to the VW DLC.

2. Open Launch CR9081, this is home menu incl. Diagnose, Record.., settings and help. Choose "Diagnose" then press the "OK" button.


3. You can see "OBDII/EOBD" and "Reset", choose " OBDII/EOBD " then press the "OK" button.


3. Entering system.


4. Monitor status.


5. Diagnostic menu: Read codes, erase codes, I/M readiness, Data stream, freeze frame, O2 sensor test, on-board monitoring, Evap system test, vehicle information and more.


6. Read codes.


7. Data stream.



View graphic items.


8. Let's go to reset function, choose any of them to go deep.
List: Bleeding, battery change, brake reset, DPF reset, ETCS reset, IMMO, Injector codeing, Oil lamp reset, steering angle reset and TPMS.





8-1: Steering angel reset for example, you can it supports 41 car brands.


What a nice feature is in the "Help" option, it offers DTC Library.



you might also like: Auro im600 manual

2018-04-27

Launch X431 Series Update Note of Easydiag, X431 V, X431 V+, PRO MINI...

Launch X431 Update note post for you. This update contains car models like VW, Audi, Land Rover, Suzuki, Volvo. Go ahead to view the update details


===========X431 VW Diagnostic Software V28.41 for EasyDiag 3.0=================
Update note:
1. Summary Optimized the quick test and system report; optimized the reading of special algorithm data streams; fixed the software access bug.
2. New Functions None
3. Optimized Functions
1) Optimized the quick test and system report.
2) Optimized the reading of special algorithm data streams.
4. Fixed Bugs Fixed the software access bug.

==============X431 AUDI Diagnostic Software for EasyDiag 3.0==============
Update note:
1. Summary Optimized the quick test and system report; optimized the reading of special algorithm data streams; fixed the software access bug.
2. New Functions None 3. Optimized Functions
1) Optimized the quick test and system report.
2) Optimized the reading of special algorithm data streams.
4. Fixed Bugs Fixed the software access bug.

==============LANDROVER Diagnostic Software V33.33====================
Support products X431 Pad II (Android)X431 PRO MINIX431 ProX431 Pro3X-431 V+X-431 VEasyDiag 3.0Easydiag 3.0+iDiagEasydiag2.0Easydiag2.0+GOLODiagun IV…
Update note:
1. Summary In this upgrade, optimized special function classification and resolved the text display problem for some special functions.
2. New Functions None
3. Optimized Functions
1) Optimized special function classification.
4. Fixed Bugs
1) Rectified the failure to perform the function Set/un-set air suspension tight tolerance mode (headlamp setting) for 2012 Land Rover Discovery.
2) Rectified the failure to perform the Headlamp control module system calibration function for 2013 Land Rover Discovery and Evoque.
3) Resolved the text display problem for some special functions.

==============Suzuki Diagnostic Software V37.10========================
Support products X431 Pad II (Android)X431 PRO MINIX431 ProX431 Pro3X-431 V+X-431 VEasyDiag 3.0Easydiag 3.0+iDiagEasydiag2.0Easydiag2.0+GOLO…
Update note
1.Summary Added the functions Read DTCs, Clear DTCs, and Data Streams for 19 IDs of the SRS and TCM systems in Japan. Added the following special functions: Aiming Adjustment, Aiming Readjustment, Show Auto Gear Shift Learning Result
2.New Functions
1)Added the functions Read DTCs, Clear DTCs, and Data Streams for 19 IDs of the SRS and TCM systems (UDS-CAN protocol).
2)Added the following special functions: Aiming Adjustment, Aiming Readjustment, Show Auto Gear Shift Learning Result
3.Optimized Functions Optimized support for the UDS-CAN protocol systems.
4.Fixed Bugs None

==============VOLVO Diagnostic Software V43.80=========================
Support products X431 VX431 V+X431 PROX431 PRO3X431 PADIIX431 Pro MiniEasyDiag 3.0Easydiag 3.0+iDiagEasydiag2.0Easydiag2.0+GOLODiagun IV…
updates as following:
I. Summary
1. Corrected the carbon particle combustion functions for 2004-2015 S40, S60, S80, C30, C70, V40, V50, XC60; added the carbon particle combustion functions for 2009 V70 and 2013 XC90.
II. New Functions
Added the carbon particle combustion function for the following:
1. 2009 V70 D5244T5 and D4204T engines
2. 2013 XC90 engine
III. Optimized Functions None
IV. Fixed Bugs Corrected the carbon particle combustion function for the following:
1. 2004-2010 S40 D4204T, D4164T, D4204T2 engines
2. 2007 S60 D5244T5 engine, 2014-2015 S60 D4204T5 engine
3. 2007-2008 S80 D5244T5 engine, 2012 S80 D5244T15 engine
4. 2007 C30 D4164T engine
5.2007 C70 D5244T8 engine
6. 2013 V40 D5204T6 engine, 2015 V40 D4204T14 engine
7. 2007 and 2009 V50 D4164T engine, 2011 V50 D5204T engine, 2013 V60 D82PHEV engine
8. 2009 XC60 D5244T5 engine, 2010 XC60 D5244T16 engine, 2012 XC60 D5244T15 engine
9. 2007 XC90 D5244T4 engine, 2011 XC90 D5244T5 engine


 Want to know more X431 Products, here is the link for you:

2018-04-24

CGDI BMW Do BMW F Series Coding Process

Here share a process about how CGDI BMW Prog key programmer do BMW F series coding

1.  Connect OBD and click BMW F series coding

2.  Choose ECU info
Note: this function needs to connect the internet, please confirm the network is smooth, click ECU info

3.  After reading ECU successfully, click 3. FEM_BODY

4.  Choose Backup coding and choose yes


Note: Coding succeed, this file is the save route

5.  Click coding

6.  Coding successfully



Thank you for reading.

How to Enable and Disable F Series Key by CGDI BMW Prog

CGDI BMW Prog is the first programmer to test BMW DME MSV80 in China. It has spotlights like BMW F series Program, BMW F series Coding, EGS ISN.
This post will share you the process how CGDI BMW enable F series key and disable F series key.

CGDI BMW enable F series key
After connecting the CGDI BMW and vehicle via OBD, click BMW enable/disable key

Then click Display key information to show the information about key


Read succeed


Choose the key position you want to enable and then click Enable the key



Put the key vertically in the key induction area of the direction column5


Enable the key successfully


CGDI BMW disable F series key
After connecting the CGDI BMW and vehicle via OBD, click BMW enable/disable key

Then click Display key information to show the information about key


Read succeed


Choose the key position you want to disable


Click Disable the key



Disable the key successfully



2018-04-23

How to use OBDSTAR H108 calibrate cluster for Citroen?

It is very easy to use OBDSTAR H108 calibrate cluster for Citroen Canbus by following the message on the screen.

Here we go for steps.
Connect OBDSTAR H108 to the Citroen BSI.


Choose "Cluster Calibrate".


Citroen




Choose "BSI".


Auto select


If auto select fail, choose "manual select".


Choose "JC BSIO4EV-KOX".


Switch ignition on


Choose "Read EEPROM".




Please enter a filename to save, press "ENT" button.


Operation success


Press "ENT" to confirm.

Read Flash...


Press "ENT" to confirm.


Read Flash success.


Press "ENT".


Press "ENT".


Press "ENT".


Enter a new value.



Success.



Done.
It's really easy to calibrate cluster for Citroen.